L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked[1] _机械 /仪表_工程科技_专业资料。ASTM A Standard.

Author: Kazragar Nikojind
Country: Spain
Language: English (Spanish)
Genre: Finance
Published (Last): 4 November 2015
Pages: 496
PDF File Size: 10.46 Mb
ePub File Size: 16.56 Mb
ISBN: 847-4-35145-750-9
Downloads: 38886
Price: Free* [*Free Regsitration Required]
Uploader: Vudozahn

One bend test shall be made from one end of each coil. D PSS means plate, strip, sheet.

ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

B Maximum unless otherwise indicated. C Annealed material that naturally meets mechanical properties may be applied. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined. Historical Version s – view previous versions of standard.

Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the adtm factor in meeting the properties.

B Type is generally produced with a chemical composition balanced asrm rich side Type or lean side Type austenite stability depending on the properties required for speci? This revision of Speci? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

  BOMBAIYER BOMBETE PDF

They shall be formed in different shapes such as sheets, strips, plates astmm flat bars. The noncontrolling factor normally will exceed considerably the speci? Only annealed conditions of grades speci? Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?

The values obtained in this manner should not, however, be taken as the actual yield strength for 0. However, in the case of dispute, tests shall be made by pressure. In case of dispute, the offset method of determining yield strength shall be used. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.

This standard has been approved for use by agencies of the Department of Defense. Current edition approved Oct.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

A — 03 Standard Speci? HardC Elongation in 2 in. Q666 International takes no position respecting the validity of any patent rights asserted in connection asgm any item mentioned in this standard. Originally approved in The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. Hard Elongation in 2 in. Rockwell B 95 95 A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

  ESDEP COURSE PDF

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Number of Tests 8. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

The values given in parentheses are for information only. Link to Active This link will always route to the current Active version of the standard. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Material Test Report aa666 Certi? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

The choice of test method for materials in conditions other than annealed shall be at the option of the seller.