Corvette Factory Assembly Manual [Chevrolet Motor Division] on Amazon. com. *FREE* shipping on qualifying offers. DAVE GRAHAM VERSION-BOUND. Corvette Owner’s Manual Reprint [GM CHEVY CHEVROLET CORVETTE VETTE] on *FREE* shipping on qualifying offers. CHEVY. These are high-quality reprints of the same manuals that a Chevrolet dealer mechanic would use to work on cars. The set includes the ” Chevrolet Chassis.

Author: Arashigal Keran
Country: Burkina Faso
Language: English (Spanish)
Genre: Love
Published (Last): 8 May 2010
Pages: 104
PDF File Size: 18.12 Mb
ePub File Size: 16.19 Mb
ISBN: 993-8-79450-428-9
Downloads: 65260
Price: Free* [*Free Regsitration Required]
Uploader: Nazil

Install drain plug and tighten.

service manual ? – CorvetteForum – Chevrolet Corvette Forum Discussion

Bend fast idle lever on Holleys. This allows the crankcase ventilation tube that is connected to the air cleaner to draw a vacuum in the crankcase when the throttle is wide open. The exterior of the Corvette also featured a number of other design cues that were new for the model year. Inspect all hose connections. Send a private message to 7T1vette.

With slow idle speed correctly adjusted, fully open choke and make sure fast idle cam follower is off steps manuak cam. Read more Read less.

1970 C3 Chevrolet Corvette: Specifications, VIN, Options, Performance, Recalls, & More

Disconnect accelerator return and trans. Amazon Renewed Refurbished products with a warranty. An air pump, diverter valve, check valve sAIR pipe assemblies and connecting hoses and fittings.

While these markings were certainly a differentiator between which engine a particular Corvette was built with, it was also readily obvious to anyone who heard the unique rumble maunal the exhaust pipes and the tapping of its mechanical lifters that they were in the presence of an LT-1 engine. Remove the air cleaner and check to see that choke valve and rod more freely.

Shopping Cart Software by AbleCommerce. Inspect spark plug hole threads and clean before installing plugs. Check distributor point spring tension contact point pressure with a spring gauge hooked to breaker lever at the contact and pull crovette at 90 degrees to the breaker lever. Withdraw the dipstick, wipe it with a clean rag, replace and withdraw again. Every 12, miles or sooner, depending on service, remove fluid from sump and add new fluid.

  BRIAN GREENE LA MAGIE DU COSMOS PDF

While earlier Corvettes were capable of being equipped with such options as the ZL-1which featured a setup that included the cubic inch L88 enginethe offerings were a little harder to come by.

Withoutabox Submit to Film Corvetge. The car, which rolled off the production line at Tighten mounting bolt and remove pin. Other Items In This Category.

Corvette America – Corvette Service Manuals

It’s only a few pages with minor differences to the ’69 manual. Push the snap lock downward until the top is flush with the rest of the cable. Adjust one idle mixture screw at a time for smoothest, fastest idle speed.

Remember that the plant was on strike that year so the ’69 model year was extended and the ’70 model year was truncated. Fortunately they can be easily replaced at many auto parts stores. Principal members — underbody, front and rear end assemblies, dash panel and hinge pillars are bonded, riveted, or bolted together and to each other.

Special tool lists can be found at the end of each section. East Dane Designer Men’s Fashion. When I google corvette service manual, the GM shop service manual comes up and on the cover it says it is for the Nova, Chevelle, MonteCarlo and corvette.

If the battery has remain undercharged, check for loose or defective fan belt, defective alternator, high resistance in the charging circuit, oxidized regulator contact points, or a low voltage setting. The adjustments described apply to all carburetors used, except as noted. A number of detail refinements were also made to the taillights and the stainless steel rocker moldings.

Due to age, the window cushions can become damaged or may fall off the vehicle. If they did not make one for a 70, should I get the one for the 71? See Transmission Modulator Vacuum Leaks above for additional information. Alan is right there is a supplement to the full ’69 manual. Bend must be such that rod enters choke lever hole freely and squarely.

  HOSPITIOUS ADOPTION PDF

If the teeth on the regulator gear are not damaged, the window motor will need to be removed from the regulator and inspected. Description Hydraulic; pump powered cylinder assisted linkage Gear Ratio This car gives the impression that it could do anything you demanded.

Quote message in reply? Last edited by Alan 71; at Steering Steering Specs — Manual Steering Type Semi-reversible gear with ball-nut driven by recirculating anti-friction bearings, energy-absorbing steering column, steering damper attached to relay rod; two position steering knuckle arm attachment for street and fast ratio steering.

In addition to the items listed above, it is also recommended that the following items are inspected every miles or 2 weeks, whichever comes first:. Replace rotor where necessary. On vehicles equipped with automatic transmission, pull through detent. If necessary, oil should be added through the filler cap. Vertical suspension loads taken by transverse leaf springs. These are high-quality reprints of the same manuals that a Chevrolet dealer mechanic would use to work on cars.

All engines are stamped on the top front of the right-hand bank of cylinder and case. Find More Posts by Ray Y. A damaged worm gear gear drive on the window motor will require replacement of the entire window motor.

Open carburetor wide open, at which point ball stud must contact end of slot in upper rod.